MH8000P Pre-Programmed TENS and EMS
The MH8000P Pre-Programmed unit integrates EMS and TENS functions with 27 preset programs and 3 programmable programs.
The preset programs are prepared in the factory according to the customer's parameters.
The programmable programs are available to be set and stored by user.
■ Our products have new technique for a comfortable output waveform.
■ TENS and EMS Two in one, our products support full TENS and EMS functions with 7 treatment modes, ideal for home health care.
■ Dual Power source: Mains power adaptor or DC 9V battery.
■ The 3 treatment phases Warming up, Treatment and Recover for each Preset Programs.
■ Large Liquid Crystal Display (LCD): Large LCD can display intensity level, settings and treatment timer at the same time. The information shown in a large font can make it easier for elder users to read.
■Key Pad control, Power, intensity level and parameter are input by Key pad. It's easy for users to input their settings. All buttons will be auto-locked after 30 seconds idle time to avoid accidental touch.
■ Adjusting Intensity Level precisely: fully digital designed, the Intensity level control by keypad buttons, Intensity Level can be increased from 0 by 1mA each step up to 80mA. Precise and smooth adjustments in Intensity Level can prevent the user a sudden adjusting the intensity of too much danger.
■ Clear Treatment Time: The treatment time count down and the balance treatment time can be read from the LCD.
■ Compliance Meter: Doctors can tell whether a patient could continue treatment in accordance with the instructions. The patient compliance timer can memorize 100 sets of therapy session records; the total record time is 400 hours.
■ ON and OFF time indicator: For EMS function, the Intensity Level that displays on the LCD screen will accordingly switch among Ramp time, ON time and OFF time. This makes it easier for the patient to know to turn up the intensity only during the ON Time, otherwise, the patient might accidentally turn the amplitude way up during the OFF Time, and suddenly have too much stimulation when the unit comes back to ON Time
■LOW BATTERY INDICATOR: A low battery indicator will flashes on the LCD only when the battery is low.
■ Our products all components are made in Taiwan, we assemble products in Taiwan, and we assure our quality.
The device detailed information:
1. Dual Channel, isolated between channels.
2. Timer setting from 5-90 Minutes, 5min./step, or continue.
3. Time count down monitored on LCD screen.
4. Automatic switch off after 30 seconds if unit is not in use.
5. CE 0434, FDA (510k)
6. Waveform: Asymmetrical rectangular biphasic pulse.
7. Amplitude: 0 - 80 mA into 500 ohm load.
8. Selectable pulse width: Adjustable, from 50us - 300us, 10us/step.
9. Pulse Rate: Adjustable, from 2 Hz - 150 Hz, 2Hz~20 Hz in 1 Hz/step and 20~ 150 Hz in 5 Hz/step.
10. Modes for EMS:
The EMS is an intermittent stimulation. The pulse active and inactive duration are adjustable by setting ON time and OFF time.
The contraction gradually increases during ramp-up time and reaches maximum contraction during ON time.
During ramp-down time, the contraction gradually decreases until the OFF time starts.
S (Synchronous) Mode:
Stimulation of both channels will occur simultaneously.
A (Alternate) Mode:
Stimulation of Channel 1 and Channel 2 will occur alternately.
11. Modes for TENS:
N (Normal) Mode:
Continuous output, pulse rate and pulse width are adjustable.
M (Mixed Frequency) Mode:
This mode has a combination of high and low frequency stimulation.
Per cycle time is 6 seconds. Each cycle contains two phases. During the first 3 sec. phase,
the Pulse Rate runs at high-frequency, then during the second 3 sec. phase, the Pulse Rate runs at low-frequency.
The cycle is then repeated. The low-frequency is fixed at 2 Hz.
The high-frequency is adjustable from 2 to 150 Hz in which from 2 to 20 Hz at 1 Hz per step and from 20 to 150 Hz at 5 Hz per step.
B (Burst) Mode:
Pulse width is adjustable from 50~300uS in 10uS per step, Frequency is fixed at 100 Hz, Burst rate is fixed at 2 Hz.
SD (Width Modulation) Mode:
Pulse Width is modulated over a period of 3 seconds from its original setting value down to 60% of its setting,
then modulated over another 3 seconds period at its original value. The cycle is then repeated.
Per cycle time is 6 seconds.
MR (Rate Modulation) Mode:
Pulse Rate is modulated over a period of 3 seconds from its original setting value down to 60% of its setting,
then modulated over another 3 seconds period at its original setting. The cycle is then repeated. Per cycle time is 6 seconds.
12. Contraction Time: Adjustable, from 2-90 seconds, 1sec./step, (EMS only).
13. Relaxation Time: Adjustable, from 2-90 seconds, 1sec./step, (EMS only).
14. Ramp Time: Adjustable, from 1-8 seconds, 1sec./step, (EMS only).
15. Patient compliance meter: The patient compliance timer can memorize 100 sets of therapy session records; the total record time is 400 hours; 240 minutes for a single therapy session.
16. Digital LCD display.
17. Low battery indicator.
18. Dual Power source: Mains power adaptor or DC 9V battery.
19. Tolerance: +/- 10%
20. AC/DC Mains power adaptor (an option accessory)