Metallux SA of Mendrisio at COMPAMED 2021 in Düsseldorf -- COMPAMED Trade Fair
Manage stand orders
Select Option

Metallux SA

Via Moree 12, 6850 Mendrisio
Switzerland

Submit your contact details

Provide your contact details to the exhibitor. Optionally, you may also add a personal message.

Please log in

You must be logged in to send the contact request.

An error has occurred

Please check your internet connection or try again later.

Message has been sent

Your message to the exhibitor was sent successfully.

Hall map

COMPAMED 2021 hall map (Hall 13): stand A75

Fairground map

COMPAMED 2021 fairground map: Hall 13

Our range of products

Product categories

  • 01  Manufacturing of components
  • 01.01  Electronic manufacturing services (EMS)
  • 01.01.03  Electronics manufacturing

Electronics manufacturing

  • 01  Manufacturing of components
  • 01.02  Plastics processing
  • 01.02.01  Injection molding

Injection molding

  • 02  Manufacturing of finished products
  • 02.09  Electromedical devices

Electromedical devices

  • 06  Electrical components, electronical components
  • 06.01  Sensors
  • 06.01.04  Pressure sensors
  • 07  Microtechnology
  • 07.01  Mechatronics

Mechatronics

Our products

Product category: Pressure sensors

ME790 - Piezoresistive Monolithic with signal conditioning

Metallux ME790 is a ceramic alumina monolithic pressure sensor working following the piezoresistive principle. The Wheatstone bridge is screen printed directly on one side of the ceramic diaphragm by means of Thick Film technology and signal conditioning electronics are added to generate 0.5...4.5 V ratiometric output SMD directly on the sensor. Pressure and temperature calibration are done electronically with the SMD ASIC and can be performed in bar (ME790) or in psi (MEP790). Electronics provide offset and span correction when temperature changes. Aging detection and compensation are constantly performed. This new method guarantees good precision and long-term stability. The Metallux ME790 family meets EMI requirements. The ASIC stores production lot specific data for sensor traceability and allows custom calibration. Due to the excellent chemical immunity of the Al2O3 ceramic, the ME790 sensors are suitable for nearly all aggressive media.

More Less

Product category: Pressure sensors

ME501 - Piezoresistive Flush Membrane

Metallux ME501/ME505 pressure sensors are made with a ceramic base cell and a flush diaphragm and work following the piezoresistive principle. The Wheatstone bridge is screen printed on one side of the flush ceramic diaphragm which is, in turn, glued to the sensors body. The bridge faces the inside where a cavity is made and the diaphragms opposite side can therefore be exposed directly to the medium to be measured. Because of the Al2O3 ceramic's excellent chemical resistance (aggressive gases, most solvents and acids, etc.), no additional protection is normally required. Metallux ME501/ME505 sensors are thermally compensated by laser adjustable PTC resistors and the use of ceramic ensures a high linearity across the entire range of measurement, reducing effects of hysteresis to a minimum.

More Less

Product category: Pressure sensors

ME600 - Piezoresistive Monolithic

Metallux ME600 monolithic pressure sensors are made with a ceramic cell and work following the piezoresistive principle. The Wheatstone bridge is screen printed directly on one side of the ceramic diaphragm by means of Thick Film technology. The diaphragms opposite side can be exposed directly to the medium to be measured. Because of the Al2O3 ceramic's excellent chemical resistance (aggressive gases, most of solvents and acids, etc.), no additional protection is normally required. Thanks to the reinforced outer area (monolithic structure), the sensor can be mounted directly in a plastic or metallic case by using O-ring. ME600 sensors are designed in such a way so that temperature changes and pressure overloads do not cause loss in reliability. Metallux ME600 sensors ensure optimal linearity across the entire range of measurement and minimize effects of hysteresis. Metallux ME600 family merges and substitutes ME662, ME663, ME651 and ME667 families.

More Less

About us

Company portrait

Vision
Metallux SA provides an exclusive range of standard and custom pressure sensors as well as developing technologically innovative hybrid solutions for projects based on customer specifications. Thanks to the technical support of its engineering team, Metallux SA offers customers a consultancy, prototyping and testing service for high quality results.

Expertise
Metallux can assist customers at multiple points in the product design process including: Feasibility studies, Prototyping, Commercialization, Mass Production & Automation. With its global presence, Metallux offers standard pressure sensors with the option of customized solutions to meet specific customer requirements. In addition, Metallux manufacturing technologies are specialized in micro-electronic assemblies and the ability to produce customized hybrid thick film circuits and COB applications.