WITTMANN BATTENFELD GmbH of Kottingbrunn at COMPAMED 2021 in Düsseldorf -- COMPAMED Trade Fair
Manage stand orders
Select Option


Wiener Neustädterstr. 81, 2542 Kottingbrunn
Telephone +43 2252 404-0
Fax +43 2252 404-1062

Submit your contact details

Provide your contact details to the exhibitor. Optionally, you may also add a personal message.

Please log in

You must be logged in to send the contact request.

An error has occurred

Please check your internet connection or try again later.

Message has been sent

Your message to the exhibitor was sent successfully.

This company is co-exhibitor of
ADVANTAGE AUSTRIA Wirtschaftskammer Österreich

Hall map

COMPAMED 2021 hall map (Hall 14): stand A20

Fairground map

COMPAMED 2021 fairground map: Hall 14

Our products

Product category: Injection molding machines

The new standard for electrical machines

The belt-free EcoPower scores with a compact injection unit and a cleanly designed clamping unit with a highly efficient direct drive. With the EcoPower, the braking energy of the drives, which is usually fed back into the power grid, is used entirely within the machine to supply power to the control system and for cylinder heating. This makes these machines extremely energy-efficient and sets a benchmark in terms of low energy consumption.

Another plus of the EcoPower is the user-friendly machine design. When developing the EcoPower, special attention was paid to small installation dimensions and compact integration.

  • Fast and precise injection and repeatable holding pressure and back pressure control
  • Clean and compact encapsulated gearbox solution
  • High energy efficiency through internal use of braking energy to power the control system and cylinder heater
  • Low space requirement and low noise emissions
  • Modular design for configuration in standard, high-performance and clean room versions

More Less

Product category: Injection molding machines

The high speed machine

The EcoPower Xpress is an exceptionally fast toggle-lever machine whose main movements are driven by water-cooled servo motors. The mold height adjustment of the clamping unit is also electrically driven. A hydraulic unit with servo motor drive is used for the secondary movements.

The machine is equipped with a highly dynamic injection unit. The feed movement for injection and the screw retraction during plasticizing are driven by two arrow-toothed double racks with symmetrical force distribution.

The clamping unit of the EcoPower Xpress is a 3-platen/4-beam system with a 5-point toggle that is self-locking in the end position, with a drive combination of servo motor and rack and pinion gear. The highly stable clamping platen is guided by a carriage on linear guides and recirculating roller bearings without tie-bar contact on the base frame.

  • Servo-electric high-performance injection molding system for thin-wall products
  • Injection units in 3 sizes for injection speeds up to 600 mm/s and injection pressures up to 2,500 bar
  • High dynamic injection acceleration 15.000 mm/s2
  • High-performance plasticizing by barrier screws
  • Maintenance-free 5-point toggle system with encapsulated central lubrication system
  • Fast-response mold protection system

More Less

Product category: Injection molding machines

Economically perfect for small and micro parts

The main benefit of the MicroPower, in addition to its unique part quality, is its cost-effectiveness. Thanks to shorter cycle times and lower material and energy consumption, cost savings of around 30 to 50 % can be achieved compared to standard machines.

From simple small parts production to the production of precision and micro injection moulded parts, the consistently further developed all-electric MicroPower offers optimum solutions thanks to its intelligent machine concept. The concept makes it possible to expand a basic machine - starting with a simple "open-close" machine for small parts - by docking modules up to a multifunctional production cell for highly complicated micro parts.

Clean room compatible standard concept
The machine housing is designed to be easy to clean as standard. The machine can be combined with a laminar flow unit, which allows class 6 clean air according to ISO 14644-1, without any design adaptation.

By combining two injection units side by side and using a rotary table in the clamping unit, a 2-component machine can easily be realized.

  • Economical, energy-efficient, resource-saving
  • Outstanding part quality due to processing of thermally homogeneous material
  • Processing of all sprayable materials up to 4 cm3 shot volume
  • Precise and powerful
  • Clean room compatible standard concept
  • Also available in COMBIMOULD design

More Less

Product category: Injection molding machines

More functionality, design quality and performance

The combination of plastics with different properties and colours to form a component in one manufacturing process and the integration of subsequent steps such as bonding, assembling and screwing, enables new property dimensions of the product with simultaneous economical production.

WITTMANN BATTENFELD know-how covers all process variants such as multi-color, composite, assembly, multi-component and sandwich injection molding. Building on the MacroPower as a basis, the MacroPower multi-component series offers the right package for all multi-component technologies with an extensive option package and the diverse combination possibilities. This means that the machine, mould and automation technology can be optimally matched to the respective product.

  • Precise machine technology with clamping system guided via linear guides and high-performance injection units
  • Injection units can be freely selected and combined
  • Fast and precise transfer of pre-moulded parts thanks to servo-electric rotary table technology
  • Independent and parallel injection of all injection units with high injection rates

More Less

Product category: Injection molding machines

The compact big one in hybrid

The MacroPower E Hybrid consists of a modern servo-hydraulic 2-platen clamping unit combined with an all-electric high-performance injection unit with injection speeds of up to 450 mm/sec. High dynamics, precision and energy efficiency enable the production of high-precision plastic parts with lowest energy consumption at the same time. This makes this machine particularly suitable for high-cavity molds from the packaging and electronics sectors as well as technical thin-walled precision parts.

With the MacroPower E Hybrid, the clamping, ejector and nozzle movements are servo-hydraulic. A highly dynamic servo motor is used as the drive. The hydraulic pump is an electrically adjustable axial piston pump with variable displacement, which is designed to meet the performance requirements of the clamping unit. The flow rate is controlled via the motor speed or the swivel angle of the hydraulic pump.

  • Highest dynamics and injection speed
  • Lowest mass moment of inertia
  • Particular precision and repeatability of the injection process
  • Lowest energy consumption
  • Extremely low noise
  • Largely maintenance-free
  • Highest economic efficiency

More Less

Product category: Injection molding machines

Compact design for space-saving production

In the CM series, the tie-bar-free clamping unit has a vertical design. The configuration of the injection unit can be horizontal or vertical. The CM is equipped with servo-controlled vertical injection units from the TM and HM series for processing TPE and various conventional thermoplastics.

The CM has a tie-bar-less vertical clamping unit. There are no interfering contours in the mold area. The vertical C-frame design with two symmetrical clamping cylinders provides maximum clearance in the mould area with optimum accessibility. The CM is mainly used for overmoulding all types of connectors and cables.

  • Optimum access for part removal and for other automation concepts thanks to the protection of the insertion and removal area by light curtains
  • Maximum free space in the mould area with optimum accessibility thanks to vertical clamping unit in C-frame design with 2 symmetrical clamping cylinders
  • Ergonomic working in semi-automatic mode thanks to reduced working height of 1,000 mm

More Less

About us

Company portrait

WITTMANN BATTENFELD Italy moves into a new building.
Completion of the new building for WITTMANN BATTENFELD France.

Expansion of the assembly hall by 2,200 m².
Extension of the sales building to create offices and meeting rooms.
Construction of a new development engineering centre.
Investment in MES manufacturer ICE-Flex.

Expansion of production capacity in Kottingbrunn.
MacroPower series is expanded up to 2,000 t clamping force.
Introduction of the new high-speed all-electric machine series EcoPower Xpress.

The WITTMANN Group celebrates its 40th birthday.Foundation of WITTMANN BATTENFELD Slovakia and South Korea.
Expansion of WITTMANN BATTENFELD Inc. in Torrington, CT by 5,000m2 of office and production space.
Expansion of WITTMANN Robottechnikai Kft. in Hungary by a third production hall, as well as a hall for the automatic production of machine frames.

Opening of the new house in Taiwan, the new bulk material production plant in Wolkersdorf near Vienna and the new sales office in Hungary.
Acquisition of BATTENFELD Poland, foundation of WITTMANN BATTENFELD Poland.

Commissioning of a new assembly hall at WITTMANN BATTENFELD in Kottingbrunn, and further expansion of the Kottingbrunn capacity for the construction of large machines.

Expansion of production capacities at WITTMANN Kunststoffgeräte GmbH in Vienna - commissioning of the new sheet metal processing facility.
Expansion of the American WITTMANN BATTENFELD subsidiary in Torrington, CT.
WITTMANN BATTENFELD France: merger of two production sites in Moirans.

Foundation of WiBa Colombia.
Expansion of WITTMANN BATTENFELD branches in Chennai (India), Kottingbrunn (Austria) and the WITTMANN branch in Nuremberg (Germany).

In the Czech Republic, WITTMANN BATTENFELD moves into a new larger building.

WITTMANN BATTENFELD product offensive with the new PowerSeries.

Groundbreaking ceremony for the WITTMANN BATTENFELD Center in Meinerzhagen (Germany).

Foundation of WITTMANN BATTENFELD Romania.

On April 1, WITTMANN takes over BATTENFELD Kunststoffmaschinen Ges.m.b.H. in Kottingbrunn (Lower Austria). The merger leads to a mutual complementation of the product lines - WITTMANN peripheral equipment on the one hand and injection molding machines from WITTMANN BATTENFELD on the other hand, to the advantage of plastics processors who increasingly demand seamless interaction between processing machine, automation and peripherals.
Foundation of WITTMANN BATTENFELD Bulgaria.